UDTR Global Rights of Nature Radar

Alternative Motor Examples - 3D Electronics - No Gas, Battery, or Burning of Fuels - Version 1 - Solar

Identification

Public canonical key

radar:r-c195c1caaeee61b790159cbed1e31cdf

Authors

Pacha, James

Reported year

2026

Reported language

en

Source type

PhysicalObject

First detected

2026-11-13T15:29:09.944670+00:00

Last metadata observation

2026-11-13T15:29:09.944670+00:00

Last HTTP verification

Not checked

Documentary abstract — original language

I will providing many different examples of Alternative Motors. I will be using with: Pacha, J. (2025). OVER UNITY - No Friction No OIL Manual Alternator  (Version 5) Zenodo. https://doi.org/10.5281/zenodo.17843274 Combining both into functioning generators. I will also be demonstrating 3d electronics and methods.  I will be posting many videos for all of this shortly.   Version 1 - Solar mixed with electromagnets: Using Solar and Angles to drive rotation by electromagnetism. When the tube is place in sunlight the sides facing the sun will kick on electro magnets. The base has a place for a north facing permanent magnet and a south facing permanent magnets. The 5V electromagnets all have there polarity facing north. Each ElectroMagnet is connected to 2 x Solar Panels that produce 5 Volts Each. These combine and are regulated by the 3D circuit in files. this allows for 8 total panels powering 4 x 5V electromagnets. the base holds the permanent magnets. The side facing sun with charge those electromagnets and repel or attract depending on permanent magnet setup. This is designed to fit on the Alternator linked above. I will be posting videos as I go along for these things. Please note these are what i consider toys to demonstrate concepts. These are not for profit or for commercial use. These are only for personal and educational use. The motor has 3 simple parts marked as solar.  Requires: 8 x 5V Solar Panels.  4 x 5V Electromagnets Since many of these are different. Please use all the correct electronic components for your specific setup. I used 4 x 5V Resistors for the electromagntets and 8 x Diodes to regulate direction. for the sources. 2 diodes to each path and the 5V resistor before the electromagnet.  After printing circuit use Conductive Copper Tape and and cover the tube. Start where there is a straight gap. After you attach rull in palms to secure to the paths. Take an exacto knife and cut the excess away. This is simple methods of creating circuits and 3d Electronics at home. All that is needed fr this is Conductive Copper Tape. I placed on TikTok to start. I will get these uploaded elsewhere as well and share those links: Video of alternator and explanation of prep: https://www.tiktok.com/t/ZP8cesWLp/ https://www.youtube.com/shorts/lt0i3B3TZjk Video of the solar motor rotor and explanation for base and how it functions: https://www.tiktok.com/t/ZP8cegQAp/ https://www.youtube.com/watch?v=NPgWwi2P9_Q Video of the 3D electronic piece: https://www.tiktok.com/t/ZP8cebCYu/ https://www.youtube.com/shorts/Cw3s-QO_Mvc Further Explanation of motor: https://www.youtube.com/watch?v=5T7vcKNurhQ Soldering completed and checks on circuit paths.  https://www.youtube.com/shorts/lkNTsEDKGCI I am waiting on one electromagnet i broke in my original designs which were too tight. I settled for adding the screw in center of each and giving extra space. That should arrive this week. I will get that put together and last two videos posted this week for this. One video showing final assembly and one video for demonstration. I will then move on to next alternative motor (version 2) and magnifying for real world use. I am attempting to keep all compact that any can use either outside or for a single area inside. Version 3 will come after another project i am prepping a demonstration for.  This is final assembly video and final explanation before demonstration: https://www.youtube.com/shorts/eC4rnJWmVww I was playing with different designs and sizes to get this actually perfect for this. I am adding diffefent things for testing. I have one for larger solar panels. I am also adding some 10,000 uF capacitors to get charge and discharge on a set rotation. Using 2 of these with a 5V 400mA solar panels will give 1amp charge and discharge in roughly .25 seconds. So 1 will give a .12 second charge and discharge etc. I am attempting to get a stronger push while using small amounts of force. If spinning this is about the speeds i want for testing. This will allow the panel coming into sunlight to not activate until it is past the repelling permanent magnet and give a bigger push away from it while being attracted more to the attracting permanent magnet. So I am looking for timed kicks for more force without having to increase size of solar panels. Currently waiting for weather to clear up as well. I have multiple versions to test all using different parts and strengths. I have finished printing the differnet solar ones for testing and have begun printing the parts for the next version. The second one may be easier to demonstrate since it does not rely on sun and weather. I will also be showing a water powered alternative motor after as well. Not what you may be thinking. The point of this is show alternative creative ways to spin a bar using science to create a function. 

Identifiers

DOI

10.5281/zenodo.22215375

Documentary context

Documentary family

unknown

Source-reported types

PhysicalObject

Publishers

Zenodo

Entity mentions are not evidence of legal recognition. Jurisdiction studied is separate from author affiliation country.

Sources

DataCite · Record 1

• Document · https://zenodo.org/doi/10.5281/zenodo.22215375

Documentary status

Relevance pending

Library

This identity is not yet included in the Legal Library.