Cold Spray and Tribological Properties of High Entropy CrMnCoFeNi Cantor Alloy and WC Composite Coatings
Identification
- Public canonical key
- radar:r-8c68feb794d29372487560f9da5aea53
- Authors
- Harfouche, Maya
- Reported year
- 2025
- Reported language
- en
- Source type
- Dissertation
- First detected
- 2026-11-13T08:39:56.777682+00:00
- Last metadata observation
- 2026-11-13T08:39:56.777682+00:00
- Last HTTP verification
- Not checked
Documentary abstract — original language
The study investigates the deposition of CrMnCoFeNi Cantor alloy and Cantor alloy/WC-based metal matrix composites (MMC) coatings using high-pressure cold spray (CS) and laser-assisted cold spray (LACS) methods. The use of LACS and the incorporation of reinforcing WC particles in the feedstock was done in an effort to increase the low cohesion strength of the CS Cantor alloy coating to, in turn, enhance the wear resistance of the Cantor-based coatings. The effect of varying LACS laser power (1 kW, 3 kW, and 4 kW) was investigated as well as that of reinforcing particle morphology as two types of WC powders were used in the MMC feedstocks (WC cast and WC/Ni agglomerated and sintered).The use of the CS and LACS solid-state deposition methods successfully preserved the single-phase FCC random solid-solution nature of the Cantor alloy feedstock in the coatings. For LACS deposition, as laser power increased, the deposition efficiency decreased. The WC particle content in the powder feedstock also reduced deposition efficiency of the MMCs. Microstructural analysis of the LACS coatings revealed that increased laser power led to particle softening, causing decreased porosity, improved splat bonding, and a decrease in nanohardness due to an annealing effect. High laser power (especially 4 kW) resulted in increased oxidation and substrate warping, causing localized cracking in the coatings. The addition of cast WC particles to the CS and LACS feedstocks improved nanohardness and reduced porosity through tamping effects during deposition. Cross-section scratch testing and multi-load micro-indentation demonstrated that LACS deposition, particularly with WC cast particles, enhanced cohesive strength compared to CS coatings. LACS coatings showed higher cohesion strength due to thermal softening upon deposition and increased particle bonding. The presence of cast WC particles in the feedstock allowed for tamping and surface activation during deposition, also enhancing the cohesion strength of the coatings. However, coatings containing WC/Ni agglomerated particles had worse cohesion due to de-cohesion within the WC/Ni agglomerates and failure of the Ni binder within the reinforcing particles themselves.Wear tests at room temperature revealed that LACS coatings produced with 1 kW and 3 kW laser power, as well as those containing proper cast WC particle morphology exhibited improved wear resistance over CS coatings. The 1 kW and 3 kW LACS Cantor coatings had lower wear rates due to higher cohesion and microhardness, which reduced particle pull-out and abrasive wear. However, the 4 kW LACS coating showed increased wear due to oxidation and thermal stress-induced fatigue. The type of WC particle morphology significantly affected wear behavior, with cast WC particles leading to a stable protective oxide tribolayer, reducing wear. In contrast, agglomerated WC/Ni particles caused extensive particle pull-out and increased wear.The study found that, like hardness, cohesion is a critical factor that governs the room-temperature tribological behavior of CS CrMnCoFeNi Cantor alloy coatings. While low cohesion in CS coatings leads to particle pull-out and abrasive wear, improved cohesion, achieved through appropriate use of the LACS process and incorporation of appropriate reinforcing particle morphology, directly enhances the wear resistance, friction stability, and hardness of the coatings. Cohesion strength, rather than hardness, was a better predictor of wear resistance in these Cantor CS and LACS coatings where particle pull-out is a limiting factor
Identifiers
- DOI
- 10.82308/24483
- OTHER
- hyrax:1544bv99w
- URI
- https://hdl.handle.net/20.500.14905/85492
- OCLC
- 1598290371
Documentary context
- Documentary family
- Thesis
- Source-reported types
- Dissertation
- Publishers
- McGill University
Entity mentions are not evidence of legal recognition. Jurisdiction studied is separate from author affiliation country.
Sources
DataCite · Record 1
Cite this reference
Harfouche, Maya. Cold Spray and Tribological Properties of High Entropy CrMnCoFeNi Cantor Alloy and WC Composite Coatings. 2025. https://doi.org/10.82308/24483
JSON · CSL-JSON · BibTeX · RIS · CSV · JSON-LD ·
APA, Chicago, ISO 690: bibliographic formats using available fields. OSCOLA / Bluebook: structured data only; full legal citation compliance is not claimed without verification of required elements.
- APA
- Harfouche, Maya. (2025). Cold Spray and Tribological Properties of High Entropy CrMnCoFeNi Cantor Alloy and WC Composite Coatings. https://doi.org/10.82308/24483
- Chicago
- Harfouche, Maya. Cold Spray and Tribological Properties of High Entropy CrMnCoFeNi Cantor Alloy and WC Composite Coatings. 2025. https://doi.org/10.82308/24483
- ISO 690
- Harfouche, Maya. Cold Spray and Tribological Properties of High Entropy CrMnCoFeNi Cantor Alloy and WC Composite Coatings. 2025. https://doi.org/10.82308/24483
Warning: Undefined array key "last_link_verified" in /home/clients/e27d81e12f04d2bfd747aa264540ac56/sites/_UDTR_APP/legal_library_reference.php on line 31
UDTR Global Rights of Nature Legal Library. Cold Spray and Tribological Properties of High Entropy CrMnCoFeNi Cantor Alloy and WC Composite Coatings. Documentary record: https://www.declarationuniverselledesdroitsdelarbre.org/global-rights-of-nature-radar/reference/r-8c68feb794d29372487560f9da5aea53/ · Last HTTP verification: not performed
Research dossiers and documentary relations
Source roles
Bibliographic / original publication source · https://mcgill.scholaris.ca/handle/20.500.14905/85492
An authority link alone does not verify a legal claim. Abstracts and full texts remain subject to their source terms.
Documentary status
Relevance pending
Library
This identity is not yet included in the Legal Library.